(Papers) SSC Junior Engineer Exam Paper - 2017 "held on 01 March 2017 "Morning Shift (General Engineering)
(Papers) SSC Junior Engineer Exam Paper - 2017 "held on 01 March 2017 "Morning Shift (General Engineering)
QID : 801 -
Options:
1) Grashoff number
2) Biot number
3) Stanton number
4) Prandtl number
Correct Answer: Biot number
QID : 802 - An ideal air compressor cycle (with clearance) on p-v diagram can be represented by ________ processes.
Options:
1) one adiabatic, two isobaric, and one constant volume
2) two adiabatic and two isobaric
3) two adiabatic, one isobaric, and one constant volume
4) one adiabatic, one isobaric, and two constant volume
Correct Answer: two adiabatic and two isobaric
QID : 803 - In a shell and tube heat exchanger, baffles are provided on the shell side to ______.
Options:
1) Prevent the stagnation of shell side fluid
2) Improve heat transfer
3) Provide support for tubes
4) All options are correct
Correct Answer: All options are correct
QID : 804 - The ratio of the thickness of thermal boundary layer to the thickness of hydrodynamic boundary layer is equal to (Prandtl number)n, where n is______.
Options:
1) - 1/3
2) - 2/3
3) 1
4) – 1
Correct Answer: - 1/3
QID : 805 - In regarding nucleate boiling _______.
Options:
1) The temperature of the surface is greater than the saturation temperature of the liquid
2) Bubbles are created by expansion of entrapped gas or vapour at small cavities in the surface
3) The temperature is greater than that of film boiling
4) All options are correct
Correct Answer: The temperature is greater than that of film boiling
QID : 806 - Boundary layer is defined as ______.
Options:
1) A thin layer at the surface where gradients of both velocity and temperature are small
2) A thin layer at the surface where velocity and velocity gradients are large
3) A thick layer at the surface where velocity and temperature gradients are large
4) A thin layer at the surface where gradients of both velocity and temperature are large
Correct Answer: A thin layer at the surface where gradients of both velocity and temperature are large
QID : 807 - Two insulating materials of thermal conductivity K and 2K are available for lagging a pipe carrying a hot fluid. If the radial thickness of each material is the same _____.
Options:
1) Material with higher thermal conductivity should be used for the inner layer and one with layer and one with lower thermal conductivity for the outer
2) Material with lower thermal conductivity should be used for the inner layer and one with higher thermal conductivity for the outer
3) It is immaterial in which sequence the insulating materials are used
4) None of these
Correct Answer: Material with lower thermal conductivity should be used for the inner layer and one with higher thermal conductivity for the outer
QID : 808 - Critical thickness of insulation for spheres is given by _____.
Options:
1) k/h
2) k/4h
3) h/2k
4) 2k/h
Correct Answer: 2k/h
QID : 809 - Which surface will have the least emissivity ?
Options:
1) Smooth glass
2) Plaster
3) Aluminium foil
4) Concrete
Correct Answer: Aluminium foil
QID : 810 - The process of heat transfer from one particle of the body to another without the actual motion of the particle, is known as ______ .
Options:
1) Conduction
2) Convection
3) Radiation
4) All options are correct
Correct Answer: Conduction
QID : 811 - The process of heat transfer from a hot body to a cold body in a straight line, without affecting the intervening medium, is known as ______.
Options:
1) Conduction
2) Convection
3) Radiation
4) All options are correct
Correct Answer: Radiation
QID : 812 - Heat is transferred from an electric bulb by ______.
Options:
1) Conduction
2) Convection
3) Radiation
4) All options are correct
Correct Answer: Radiation
QID : 813 - Assumption made in the Fourier's law is that the heat flow
A. Is in steady state
B. Through a solid medium in one dimension
Options:
1) Only (A)
2) Only (B)
3) Both (A) and (B)
4) None of these
Correct Answer: Both (A) and (B)
QID : 814 - If thermal conductivity of a material of wall varies as K_0 (1 + αt), then the temperature at the centre of the wall as compared to that in case of constant thermal conductivity, will be ______.
Options:
1) More
2) Less
3) Same
4) Depend on other factors
Correct Answer: More
QID : 815 - With increase in temperature, thermal conductivity of air ______.
Options:
1) Increases
2) Decreases
3) Remains the same
4) None of these
Correct Answer: Increases
QID : 816 - Liquid metal having highest thermal conductivity is of _______.
Options:
1) Sodium
2) Potassium
3) Lead
4) Mercury
Correct Answer: Sodium
Candidate Answer: Mercury
QID : 817 - Minimum thermal diffusivity is of ______.
Options:
1) Aluminium
2) Rubber
3) Iron
4) Lead
Correct Answer: Rubber
QID : 818 - Critical radius of a hollow cylinder is defined as _______.
Options:
1) Outer radius which gives maximum heat flow
2) Outer radius which gives minimum heat flow
3) Inner radius which gives minimum heat flow
4) Inner radius which gives maximum heat flow
Correct Answer: Outer radius which gives maximum heat flow
QID : 819 - Heat exchangers are used in
A. Condensers and boilers in steam plants
B. Radiators
C. Intercoolers and preheaters
D. Condensers and evaporators in refrigerators and air conditioners
Options:
1) Only A
2) Only B
3) Only C
4) A, B, C and D
Correct Answer: A, B, C and D
QID : 820 - Automobile radiator is a heat exchanger of _____ type.
Options:
1) Counter flow
2) Parallel flow
3) Cross flow
4) Regenerator
Correct Answer: Cross flow
QID : 821 - For a closed system, difference between the heat added to the system and work done by the gas, is equal to the change in_____.
Options:
1) Enthalpy
2) Entropy
3) Internal energy
4) Temperature
Correct Answer: Internal energy
QID : 822 - The sequence of process that eventually returns the working substance to its original state, is known as ______.
Options:
1) Event
2) Thermodynamic cycle
3) Thermodynamic property
4) None of these
Correct Answer: Thermodynamic cycle
QID : 823 - According to Kelvin-Plank's statement, a perpetual motion machine of _______.
Options:
1) First kind is possible
2) First kind is impossible
3) Second kind is impossible
4) Second kind is possible
Correct Answer: Second kind is impossible
Click Here To Download PDF
DOWNLOAD SSC J.E. SOLVED Question Papers PDF
DOWNLOAD SSC JUNIOR ENGINEER Exam General Awareness PDF
DOWNLOAD SSC CGL (Tier-1) 2020 SOLVED Question Papers PDF
DOWNLOAD SSC CHSL (10+2) Exam SOLVED Question Papers PDF
Study Material for Junior Engineer (Civil / Electrical / Mechanical Engineering) Examination
Study Kit for SSC CGL EXAM
QID : 824 - According to kinetic theory of gases, at absolute zero ______.
Options:
1) Specific heat of molecules reduces to zero
2) Kinetic energy of molecules reduces to zero
3) Volume of gas reduce to zero
4) Pressure of gas reduce to zero
Correct Answer: Kinetic energy of molecules reduces to zero
QID : 825 - According to Gay-Lussac's law for perfect gases, the absolute pressure of given mass varies directly as _______.
Options:
1) Temperature
2) Absolute temperature
3) Absolute temperature, if volume remains constant
4) Product of absolute temperature and volume
Correct Answer: Absolute temperature, if volume remains constant
QID : 826 - Three states of matter are distinguished with respect to molecules by the ______.
Options:
1) Atoms in molecules
2) Number
3) Orientation
4) Character of motion
Correct Answer: Character of motion
QID : 827 - Equal volume of all gases, at the same temperature and pressure, contain equal number of molecules. This is according to _______.
Options:
1) Charle's law
2) Avagardo's law
3) Joule's law
4) Gay Lussac law
Correct Answer: Avagardo's law
QID : 828 - Specific heat of a gas, Cp = Cv, at
Options:
1) Absolute zero
2) Critical temperature
3) Triple point
4) All temperatures
Correct Answer: Absolute zero
QID : 829 - The specific heat at constant volume of solids obeys Debye's T3 law at ______.
Options:
1) High temperatures
2) Low temperatures
3) High pressures
4) All temperatures
Correct Answer: All temperatures
QID : 830 - A reversible process _____.
Options:
1) Must pass through a continuous series of equilibrium states
2) Leaves no history of the events in surroundings
3) Must pass through the same states on the reversed path as on the forward path
4) All options are correct
Correct Answer: All options are correct
QID : 831 - In Red Wood Viscometer ______.
Options:
1) Absolute value of viscosity is determined
2) Part of the head of fluid is utilised in overcoming friction
3) Fluid discharges through orifice with negligible velocity
4) Comparison of viscosity is done
Correct Answer: Absolute value of viscosity is determined
QID : 832 - A rotameter is a device used to measure ______.
Options:
1) Velocity of fluid in pipes
2) Velocity of gauges
3) Votex flow
4) Flow of fluids
Correct Answer: Flow of fluids
QID : 833 - Steady flow occurs when ______.
Options:
1) Pressure does not change along the flow
2) Velocity does not change
3) Conditions change gradually with time
4) Conditions do not change with time at any point
Correct Answer: Conditions do not change with time at any point
QID : 834 - If the particles of a fluid attain such velocities that vary from point to point in magnitude and direction as well as from instant, the flow is _______.
Options:
1) Uniform flow
2) Steady flow
3) Turbulent flow
4) Laminar flow
Correct Answer: Turbulent flow
QID : 835 - Flow occurring in a pipeline when a valve is being opened is ______.
Options:
1) Steady
2) Unsteady
3) Laminar
4) Vortex
Correct Answer: Unsteady
QID : 836 - For measuring flow by a Venturimeter, it should be installed in _______.
Options:
1) Vertical line
2) Horizontal line
3) Inclined line with upward flow
4) In any direction and in any location
Correct Answer: In any direction and in any location
QID : 837 - A streamline is defined as the line ______.
Options:
1) Parallel to central axis flow
2) Parallel to outer surface to pipe
3) Of equal velocity in a flow
4) Along with the pressure drop is uniform
Correct Answer: Of equal velocity in a flow
QID : 838 - The purpose of surge tank in a pipe line is to _______.
Options:
1) Smoothen the flow of water
2) Compensate friction losses in pipe
3) Prevent occurrence of hydraulic jump
4) Relieve pressure due to water hammer
Correct Answer: Compensate friction losses in pipe
QID : 839 - The resultant upward pressure of a fluid on a floating body is equal to the weight of fluid displaced by the body. This definition is according to _______.
Options:
1) Buoyancy
2) Equilibrium of a floating body
3) Archimedes' principle
4) Bernoulli's theorem
Correct Answer: Buoyancy
QID : 840 - A balloon lifting in air follows the ______.
Options:
1) Law of gravitation
2) Archimedes principle
3) Principle of buoyancy
4) All options are correct
Correct Answer: All options are correct
QID : 841 - Hydraulic grade line as compared to the centre line of conduct ______.
Options:
1) Should be always above
2) Should be always below
3) Should always be parallel
4) May be above or below
Correct Answer: Should be always above
QID : 842 - A Piezometer cannot be used for pressure measurement in pipes when _______.
Options:
1) Pressure difference is low
2) Velocity is high
3) Fluid in the pipe is a gas
4) Fluid is highly viscous
Correct Answer: Fluid in the pipe is a gas
QID : 843 - A Hot Wire Anemometer is used for the measurement of ______.
Options:
1) Pressure of gases
2) Velocity of gases
3) Viscosity of gases
4) Viscosity of liquids
Correct Answer: Velocity of gases
QID : 844 - Friction drag is generally larger than the pressure drag in _______.
Options:
1) Flow past a sphere
2) Flow past a cylinder
3) Flow past an airfoil
4) Flow past a thin sheet
Correct Answer: Flow past a cylinder
QID : 845 - If one of the wall moves in the direction of flow with uniform velocity while the other wall is stationary, then the resulting flow between parallel walls is called ______.
Options:
1) Plug flow
2) Stoke's flow
3) Couette flow
4) Euler's flow
Correct Answer: Plug flow
QID : 846 - The ratio of the energy absorbed by the body to total energy falling on it is called _____.
Options:
1) absorptive power
2) emissive power
3) emissivity
4) None of these
Correct Answer: absorptive power
QID : 847 - In a flow field, at the stagnation point _______.
Options:
1) Pressure is zero
2) velocity of fluid is zero
3) Pressure head is equal to velocity
4) All the velocity head is converted into pressure head
Correct Answer: velocity of fluid is zero
QID : 848 - Viscosity is the most important property in the ______.
Options:
1) Travel of a bullet through air
2) Water jet issuing from a fire air
3) Formation of soap bubbles
4) Flow of castor oil through a tube
Correct Answer: Formation of soap bubbles
QID : 849 - If pressure at any point in the liquid approaches the vapor pressure, liquid starts vaporising and creates pockets or bubbles of dissolved gases and vapours. This phenomenon is ______.
Options:
1) Surface tension
2) Adhesion
3) Vaporisation
4) Cavitation
Correct Answer: Surface tension
QID : 850 - The fluid forces considered in the Navier-Strokes equation are ______.
Options:
1) Gravity, pressure and viscous
2) Gravity, pressure and turbulent
3) Pressure, viscous and turbulent
4) Gravity, viscous and turbulent
Correct Answer: Gravity, pressure and viscous
QID : 851 - Hydraulic grade line for any flow system as compared to energy line is ______.
Options:
1) Above
2) Below
3) At same level
4) Uncertain
Correct Answer: Below
QID : 852 - To avoid vaporisation in the pipe line, the pipe line over the ridge is laid such that it is not more than _____.
Options:
1) 2.4 m above the hydraulic gradient
2) 6.4m above the hydraulic gradient
3) 10.0 m above the hydraulic gradient
4) 5.0 m above the hydraulic gradient
Correct Answer: 2.4 m above the hydraulic gradient
QID : 853 - The locus of elevations that water will rise in a series of pitot tube is called ______.
Options:
1) Hydraulic grade line
2) Pressure head
3) Energy grade line
4) Head loss
Correct Answer: Energy grade line
QID : 854 - Pressure in Pascals at a depth of 1 m below the free surface of a body of water will be equal to _______.
Options:
1) 1 Pa
2) 98.1 Pa
3) 981 Pa
4) 9810 Pa
Correct Answer: 9810 Pa
QID : 855 -
Options:
1) 16.28 cm
2) 17.28 cm
3) 19.28 cm
4) 25.28 cm
Correct Answer: 19.28 cm
QID : 856 - If a pump is handling water and is discharging a certain flow Q at a constant total dynamic head requiring a definite B.H.P., the same pump when handling a liquid of specific gravity 0.75 and viscosity nearly same as of water would discharge
Options:
1) same quantity of liquid
2) 0.75Q
3) Q/0.75
4) 1.5Q
Correct Answer: same quantity of liquid
QID : 857 - A 20 cm diameter pipe 5000 metres long conveys 0.05 cumec of water which is to be pumped through a height of 6 metres. What is the horse power required by the pump, if its efficiency is 75 % ?(take 4f = 0.006)
Options:
1) 74.2 HP
2) 74 HP
3) 75 HP
4) 50 HP
Correct Answer: 74.2 HP
QID : 858 - For laminar flow in a pipe, V is equal to
Options:
1) Umax
2) 0.5 Umax
3) 0.25 Umax
4) 2 Umax
Correct Answer: 0.5 Umax
QID : 859 - Water at 20° C flowing through a 20 cm diameter pipe. Take kinematic viscosity of water at 20°C is equal to 0.0101 stoke. Assume that the changes from laminar to turbulent at Re = 2320. The critical velocity will be _____.
Options:
1) 1.117 cm/sec
2) 11.17 cm/sec
3) 111.7 cm/sec
4) 1.117 m/sec
Correct Answer: 1.117 cm/sec
QID : 860 - Surge wave is an example of _____.
Options:
1) Steady uniform flow
2) Steady non-uniform flow
3) Unsteady uniform flow
4) Unsteady non-uniform flow
Correct Answer: Unsteady non-uniform flow
QID : 861 - Quick return mechanism is an inversion of _____.
Options:
1) Four bar chain
2) Single slider crank chain
3) Double slider crank chain
4) Crossed slider crank chain
Correct Answer: Single slider crank chain
QID : 862 - In gears, interference takes place when _____.
Options:
1) Tip of a tooth of a mating gear digs into the portion between base and root circles
2) Gears do not move smoothly in the absence of lubrication
3) Pitch of the gear is not same
4) Gear teeth are undercut
Correct Answer: Tip of a tooth of a mating gear digs into the portion between base and root circles
QID : 863 - In a multiple V belt drive, when a single belt is damaged, it is preferable to change the complete set to _____.
Options:
1) Reduce vibration
2) Reduce slip
3) Ensure uniform loading
4) Ensure proper alignment
Correct Answer: Ensure proper alignment
QID : 864 - The centre of gravity of the coupler link in a 4-bar mechanism would experience _____.
Options:
1) No acceleration
2) Only linear acceleration
3) Only angular acceleration
4) Both linear and angular accelerations
Correct Answer: Both linear and angular accelerations
QID : 865 - The amplitude of underdamping a small damping varies with time as _____.
Options:
1) Linearly
2) Arithmetically
3) Geometrically
4) Exponentially
Correct Answer: Exponentially
QID : 866 - Whirling speed of a shaft coincide with the natural frequency of the _____.
Options:
1) Longitudinal vibration
2) Transverse vibration
3) Torsional vibration
4) Coupled between torsional vibration
Correct Answer: Transverse vibration
QID : 867 - A mass of 1 kg is attached to the end of a spring with stiffness 0.7 N/mm. The critical damping coefficient of this system is ____.
Options:
1) 1.40 Ns/m
2) 18.522 Ns/m
3) 52.92 Ns/m
4) 529.20 Ns/m
Correct Answer: 52.92 Ns/m
QID : 868 - Rankine's theory of failure is applicable for which of the following type of materials?
Options:
1) Brittle
2) Ductile
3) Elastic
4) Plastic
Correct Answer: Brittle
QID : 869 - The shock absorbing capacity of a bolt can be increased by _____.
Options:
1) Tightening it properly
2) Increasing shank diameter
3) Grinding the shank
4) Using washer
Correct Answer: Grinding the shank
QID : 870 - Which if the following key is under compression rather than in being shear when under load?
Options:
1) Saddle
2) Barth
3) Feather
4) Kennedy
Correct Answer: Barth
QID : 871 - Shaft is subjected to which of the following stresses?
Options:
1) Bending
2) Torsional
3) Both bending and torsional
4) None of these
Correct Answer: Both bending and torsional
QID : 872 - Which of the following is self-aligning bearing?
Options:
1) Conical
2) Spherical
3) Rectangular
4) None of these
Correct Answer: Spherical
QID : 873 - Which of the following is Trapezoidal thread?
Options:
1) Acme
2) Square
3) Buttress
4) All options are correct
Correct Answer: Acme
QID : 874 - The efficiency of self-locking screw is _____.
Options:
1) More than 50%
2) Less than 50%
3) Equal to 50%
4) None of these
Correct Answer: Less than 50%
QID : 875 - The most suitable bearing for carrying very heavy loads with slow speed is _____.
Options:
1) Hydrodynamic bearing
2) Ball bearing
3) Roller bearing
4) Hydrostatic bearing
Correct Answer: Hydrostatic bearing
QID : 876 - The outside diameter of a hollow shaft is twice it's inside diameter. The ratio of its torque carrying capacity to that of a solid shaft of the same material and the same outside diameter is _____
Options:
1) 15/16
2) 3/4
3) 1/2
4) 1/16
Correct Answer: 15/16
QID : 877 - A solid shaft can resist a bending moment of 3 kNm and a twisting moment of 4 kNm together, then the maximum torque that can be applied is _____.
Options:
1) 7.0 kNm
2) 3.5 kNm
3) 4.5 kNm
4) 5.0 kNm
Correct Answer: 5.0 kNm
QID : 878 - Under torsion, brittle materials generally fail ______.
Options:
1) Along a plane perpendicular to its longitudinal axis
2) In the direction of minimum tension
3) Along surfaces forming a 45° angle with the longitudinal axis
4) Not in any specific manner
Correct Answer: Along surfaces forming a 45° angle with the longitudinal axis
QID : 879 - The shear stress distribution over a rectangular cross-section of a beam follows _____.
Options:
1) A straight line path
2) A circular path
3) A parabolic path
4) An elliptical path
Correct Answer: A parabolic path
QID : 880 - When two mutually perpendicular principal stresses are unequal but alike, the maximum shear stress is represented by _____.
Options:
1) The diameter of the Mohr's circle
2) Half the diameter of the Mohr's circle
3) One-third the diameter of the Mohr's circle
4) One-fourth the diameter of the Mohr's circle
Correct Answer: Half the diameter of the Mohr's circle
QID : 881 - The plane of maximum shear stress has normal stress that is _____.
Options:
1) Maximum
2) Minimum
3) Zero
4) None of these
Correct Answer: Zero
QID : 882 - Consider the following theories of failure:
A. Maximum stress theory
B. Maximum strain theory
C. Maximum shear stress theory
D. Maximum energy or distortion theory
The most suitable for ductile material i
Options:
1) A and B
2) A and C
3) A and D
4) C and D
Correct Answer: C and D
QID : 883 - For ductile materials, the most appropriate failure theory is _____.
Options:
1) Maximum shear stress theory
2) Maximum principal stress theory
3) Maximum principal strain theory
4) Shear strain energy theory
Correct Answer: Maximum shear stress theory
QID : 884 - All the failure theories give nearly the same result _____.
Options:
1) When one of the principal stresses at a point is larger in comparison to the other
2) When shear stresses act
3) When both the principal stresses are numerically equal
4) For all situations of stress
Correct Answer: When one of the principal stresses at a point is larger in comparison to the other
QID : 885 - From the hypothesis given by Rankine, the criteria for failure of brittle material is _____.
Options:
1) Maximum principal stress
2) Maximum strain energy
3) Maximum shear stress
4) Maximum shear strain energy
Correct Answer: Maximum principal stress
QID : 886 - In a closed helical spring subjected to an axial load, other quantities remaining the same, if the wire diameter is doubled and mean radius of the coil is also doubled, then stiffness of spring when compared to original one will become _____.
Options:
1) Twice
2) Four times
3) Eight times
4) Sixteen times
Correct Answer: Twice
QID : 887 - The Poisson's ratio for most of the materials is close to _____.
Options:
1) 1 : 2
2) 1 : 3
3) 1 : 4
4) 1 : 5
Correct Answer: 1 : 3
QID : 888 - True stress represents the ratio of _____.
Options:
1) Average load and average area
2) Average load and maximum area
3) Maximum load and maximum area
4) Instantaneous load and instantaneous area
Correct Answer: Instantaneous load and instantaneous area
QID : 889 - For an element under the effect of biaxial state of normal stress, the normal stresses are on a 45 ° plane is equal to _____.
Options:
1) Difference of normal stresses
2) Sum of normal stresses
3) Half of the sum of normal stresses
4) Half of the difference of normal stresses
Correct Answer: Half of the sum of normal stresses
QID : 890 - For a thin spherical shell subjected to internal pressure, the ratio of volumetric strain to diametrical strain is _____.
Options:
1) 5 : 4
2) 3 : 2
3) 2 : 1
4) 3 : 1
Correct Answer: 3 : 1
QID : 891 - Stud and projection welding belong to the following category of welding _____.
Options:
1) gas welding
2) arc welding
3) resistance welding
4) pressure welding
Correct Answer: resistance welding
QID : 892 - Electrode gets consumed in the following welding process _____.
Options:
1) gas
2) resistance
3) thermit
4) arc
Correct Answer: arc
QID : 893 - The strength of a properly welded joint as compared to base metal would be _____.
Options:
1) same
2) more
3) less
4) unpredictable
Correct Answer: more
QID : 894 - Oxygen to acetylene ratio in case of carburising flame is _____.
Options:
1) 0.5 : 1
2) 0.9 : 1
3) 1 : 1
4) 1 : 1.2
Correct Answer: 0.9 : 1
QID : 895 - For steel castings, the following type of sand is better _____.
Options:
1) fine-grain
2) coarser-grain
3) medium grain
4) fine-grain, coarser-grain and medium grain all are equally good
Correct Answer: coarser-grain
QID : 896 - Hot tear refers to _____.
Options:
1) casting defect
2) process of fabrication
3) process of heat treatment
4) weathering of non-ferrous materials
Correct Answer: casting defect
QID : 897 - Slick in a foundry shop is used to _____.
Options:
1) make and repair corners in a mould
2) thoroughly mix up moulding sand
3) make venting holes in the mould
4) prepare gates
Correct Answer: make and repair corners in a mould
QID : 898 - Which of the following processes would produce best components?
Options:
1) die casting
2) hot rolling
3) extrusion
4) forging
Correct Answer: die casting
QID : 899 - A sprue hole is _____.
Options:
1) a casting defect
2) a hold made for riveting
3) a blind hole in jigs
4) an opening in mould for pouring molten metal
Correct Answer: an opening in mould for pouring molten metal
QID : 900 - Coining is the operation of _____.
Options:
1) cold forging
2) hot forging
3) cold extrusion
4) piercing
Correct Answer: cold forging
Click Here To Download PDF
DOWNLOAD SSC J.E. SOLVED Question Papers PDF
DOWNLOAD SSC JUNIOR ENGINEER Exam General Awareness PDF
DOWNLOAD SSC CGL (Tier-1) 2020 SOLVED Question Papers PDF
DOWNLOAD SSC CHSL (10+2) Exam SOLVED Question Papers PDF
Study Material for Junior Engineer (Civil / Electrical / Mechanical Engineering) Examination
Study Kit for SSC CGL EXAM
<<Go Back To Main Page
Whats Hot!
Important Links
Downloads
- New! SSC CGL 10+ Years Papers 2010-2023
- New! SSC CHSL 10+ Years Papers 2008-2024
- New! SSC MTS 10+ Years Papers
- New! SSC JE 10+ Years Papers
- New! SSC Stenographers Papers
- New! SSC IMD Years Papers
- New! SSC Constables (GD) Papers
- New! SSC CPO 10+ Years Papers
- PDF Study Notes for SSC Exams
- E-books Download